22 Savage Hi Power rabbit hole

I think I'm going down a major rabbit hole but want to try it anyway. I have a Krag that was sleeved to 22 Hi-Power and am not having much success with the 70 gr. Hornady's I have so I'd like to try cast and go to .228 bullets. I'm thinking there are several ways to go about it, get a mold specially made which may or may not be possible, seems most mold manufactures don't want to go below 25 cal. on special order. I've also considered running a 6mm cast through a sizing die to bring it down to .228, or swaging .225 up to .228, either way I would think it would have to be fairly soft cast. Or I could look into powder coating to try and increase the size. I've never powder coated so it would be a new experience which is quite attractive just not sure I could get them up to .228. Or maybe someone has another better idea. Like I said, it's something I want to play with, I'm newly retired and finally have time to try stuff I've not been able to do before. Any thoughts would be appreciated. Thanks.
 
I have a .22 High Power. Somewhere have an oversized mold for it. Haven't done much with it since I got it.

Gnoahh is a member here snd has forgotten more about Savage 99s in general and the .22 High Power in particular than most of us could ever learn. Hopefully he'll chime in.

He told me once that Hornady bullt is too long for the twist in the old 99s. Seems he made a file die to take a hair off the nose for a loss of like two grains which made them shoot much better.
 
If I have not already gifted it to someone else, I have a .228" Lyman or Ideal which needs a home.

I have to look.

EDIT: My apologies, @Remingtonroller* , it seems it was one of several I have sent off lately and did not keep track of.
If you like that gun, a custom mould would be worth the money and the wait.
BUT, I'd try PC first. I got some help from a few folks here on that and with the minimal investment of $18 for a pound of Eastwood Light Ford Blue(?), I've PC'd picture-perfect bullets from the very first batch. I DO have a couple (maybe three) Lyman SC .225 moulds I don't need if you don't have a 22 mould. I'll even send some gas checks to get you started.
 
Last edited:
I have a .22 High Power. Somewhere have an oversized mold for it. Haven't done much with it since I got it.

Gnoahh is a member here snd has forgotten more about Savage 99s in general and the .22 High Power in particular than most of us could ever learn. Hopefully he'll chime in.

He told me once that Hornady bullt is too long for the twist in the old 99s. Seems he made a file die to take a hair off the nose for a loss of like two grains which made them shoot much better.
Ken Waters in his Pet Loads book says to trim from .850 down to .800 and that helps. Another possibility. Thanks.
 
Let me know if you still have it. Thanks.
I went and looked and I don't have it. I'm sorry for not looking first. I've sent several moulds off in the past few months, but have been to busy to keep track.

BUT, I think the PC idea is worth looking into. I can donate a 225 mould and gas checks if you're willing to try PC. Don't get me wrong - I am not a PC-only caster, but I have, I can and it has its uses. PLUS, it's easy and inexpensive to try it. My very first batch came out perfect and I've not had one bad (or even mediocre) batch yet.

I have an old RB in "7mm SM" I may have to do PC with (don't know yet), but a generous forum-member here gifted me a mould in 7mm to try, so I'll do what I can to see you get to see that old Krag shoot.
 
I had an 1899 .22 Hi Power for a short while in my youthful gun trading days. It was a ranch rescue gun, a bit cobby but had a Lyman peep on it.
I tried to hit a paper plate at 50 yards using Norma 5.6x52R ammo and the shots were scattered randomly. So I traded it for a 336 30-30 at a gun show.
If you can find some, try some vintage Sisk .227” jacketed bullets to set a baseline.
I was given some years ago in 63gr and 70 gr semi spitzer form.
Not having a 22 HP; I sized them to .225” and used them in the 22-250. They weren’t match accurate(2”@100yds) but they killed deer just fine.
 
I went and looked and I don't have it. I'm sorry for not looking first. I've sent several moulds off in the past few months, but have been to busy to keep track.

BUT, I think the PC idea is worth looking into. I can donate a 225 mould and gas checks if you're willing to try PC. Don't get me wrong - I am not a PC-only caster, but I have, I can and it has its uses. PLUS, it's easy and inexpensive to try it. My very first batch came out perfect and I've not had one bad (or even mediocre) batch yet.

I have an old RB in "7mm SM" I may have to do PC with (don't know yet), but a generous forum-member here gifted me a mould in 7mm to try, so I'll do what I can to see you get to see that old Krag shoot.
Thanks for looking anyway, I appreciate it. I have an NOE 225407 which is 68 grain so that should work.
 
Ken Waters in his Pet Loads book says to trim from .850 down to .800 and that helps. Another possibility. Thanks.
I went out and chucked up a Hornady in the lathe, if I take the lead point of to the jacket it ends up at .778 instead of .800. Doing it that way takes about 15 seconds each. I'm going to do 5-10 and load them up to see what results I get.
 
Last edited:
Thanks for looking anyway, I appreciate it. I have an NOE 225407 which is 68 grain so that should work.
I have Jeff H's 228-367 2 cavity mould. He gifted it to me and I paid his shipping cost. I don't have a .22 Sav. Hi-Power but a friend does. I cast him up an ice cube tray of bullets. So he's all set.
Do you want me to cast you some or would you rather have the mould? Either way is fine for me.
Cost of shipping only.
 
Thanks for looking anyway, I appreciate it. I have an NOE 225407 which is 68 grain so that should work.
Unless you're an absolute glutton for punishment, DO NOT BUY THAT MOULD! I have one here somewhere, and no matter what I tried, it refused to fill out. Extra heat, pressure casting with a ladle, venting the top slit of the blocks, and even venting between cavities didn't help.

NOE's always cast about .001" over spec for me. Al has .227" designs listed, presumably for 5.56x45 throats.

Powder coating will add diameter, and some powders more than others.

I don't recall what the twist is in the 22 HiPower, but I would suggest that you don't try to go heavy or long for that twist. If its 1-14", consider the Lee 22-55 and powder coat it.
 
Unless you're an absolute glutton for punishment, DO NOT BUY THAT MOULD! I have one here somewhere, and no matter what I tried, it refused to fill out. Extra heat, pressure casting with a ladle, venting the top slit of the blocks, and even venting between cavities didn't help.

NOE's always cast about .001" over spec for me. Al has .227" designs listed, presumably for 5.56x45 throats.

Powder coating will add diameter, and some powders more than others.

I don't recall what the twist is in the 22 HiPower, but I would suggest that you don't try to go heavy or long for that twist. If its 1-14", consider the Lee 22-55 and powder coat it.
Which mould are you reffering to?
 
I have Jeff H's 228-367 2 cavity mould. He gifted it to me and I paid his shipping cost. I don't have a .22 Sav. Hi-Power but a friend does. I cast him up an ice cube tray of bullets. So he's all set.
Do you want me to cast you some or would you rather have the mould? Either way is fine for me.
Cost of shipping onl
Message sent
 
Last edited: