Shooting shack construction underway!

Intheshop

Banned
"Salt treated"

Back when this product was introduced.....say,early 70's.... salt treated was a common name for it.

OK,this is too funny to not mention..... and don't get your pantys in a wad. We used to call it "Jim Baker" wood.... swear,pick up the phone,order several thousand $$$ worth of Jim Baker and the dispatch knew EXACTLY what we were referring to. "PTL" wood....

But,back to salt treated.

Tripping on back..... uhhh,colonial Va ring a bell? Just like a Ceasar salad,ain't.... if you aren't rubbing sardines into a wood bowl at first blush.... a "salt treated" table in colonial times was the side yard tables,this is the area between the smoke house and the main kitchen where salt cured hams were inspected. The salt,just like driftwood (we are a coastal state),would permeate these tables. I've seen them show up a hundred years later and are pert near as original.
 
Last edited:

Brad

Benevolent Overlord and site owner
Staff member
Damn Ian, that sucker is gonna be weather tight! A little caulk between the logs and she will never get wet inside.

Impressive work
 

Ian

Notorious member
Yeppers. Probably will do the end logs next and get them spiked down to make sure the long logs don't shift, then do the floor logs. One of the next end logs will get notched down in the middle for the door sill.
 

Kevin Stenberg

Well-Known Member
Ian you are putting a raised plank floor at about the height of the last picture, correct? Are you going to fill the open space under the first row of logs on all sides of the building? I was just thinking of small critters getting under the building and getting into the cabin area and giving you some nasty surprises. Thinking Bees - spiders - snakes - that thing with the curly tail and stinger.
 

Ian

Notorious member
I'm just going to leave it open so it doesn't attract snakes. The inside will be sealed up tightly enough to keep critters out...hopefully.
 

Ian

Notorious member
I'm leaning toward pressure-treated 3/4" plywood at the moment. Ideas? The floor logs will be on 16" centers.
 

Brad

Benevolent Overlord and site owner
Staff member
Plywood with the joints nice and tight should keep the bugs down.
I can’t see why you would use anything else.
 

Winelover

North Central Arkansas
Composite tongue and groove...................never have to replace. Non slip surface, even when wet.
 

Bret4207

At the casting bench in the sky. RIP Bret.
In your dry climate is PT even needed? I would think standard T+G 3/4" would work fine. Last for decades if protected from weather even up here in the wet-East.
 

Ian

Notorious member
Bret, #2 kid is due in October. I probably won't have time to put a roof on this by then, and no telling how many months after.. I want to put my bench back on the platform asap anyway and it will get a lot of weather, plus is bug resistant, and is only $4 more per sheet.
 

Ian

Notorious member
Composite tongue and groove...................never have to replace. Non slip surface, even when wet.

Link? I looked and couldn't find any tg composite here. If composite it must be tg because it all is so insanely weak/rubbery.
 

Rick

Moderator
Staff member
Link? I looked and couldn't find any tg composite here. If composite it must be tg because it all is so insanely weak/rubbery.

Not so if properly constructed. I built my deck topped with composite decking. NOT T&G and no sag or spring in it anywhere. Pressure treated 2x6 frame on 12 inch centers. I didn't want T&G because it's not covered and I didn't want it to hold water. I can assure you there is nothing rubbery about it. Will outlast me probably by a few decades.
 

Ian

Notorious member
12" centers will support cooked spaghetti. Do you rememer what brand your stuff was?
 

Brad

Benevolent Overlord and site owner
Staff member
I would go pressure treated for bug protection as much as anything.


A few others out there as well.
 
  • Like
Reactions: Ian

Rick

Moderator
Staff member
Don't remember the brand, got it delivered from Lowes. I left about a 1/16" gap between the decking so that it would drain water and it does very well, rain or when I pressure wash it. John's deck is under cover and T&G was a good choice for him, not for me.